COOLER MASTER Hyper 212 Plus RR-B10-212P-G1 120mm sleeve CPU Cooler

Comment:
got this to replace intel stock cooler (i5 760). quieter operation and lower temps. just a great purchase

Comment:
I have an i7-875K so I really need a good CPU cooler. This one does the job and no matter how I OC my CPU, it doesn't make noise, I can bearly hear it. The best thing for this cooler is the price, you can't get any better cooler than this one for less than 30 bucks.

Comment:
Very impressed with this product. It offers great cooling performance at a low cost.The Intel stock HSF allows my E5200 (OC 3.33ghz) to rise over 70c under full load. My chasis doesn't have great air flow, but after installing this, the CPU temperature always stay under 60c. The fan is not noticeably louder than the Intel Stock one either.The installation is a little tricky since you have to take your motherboard out of the case but it took me no more than 30 min.

Comment:
Using this on an OC'd Intel E8400 and it works like a charm keeping my OC'd baby in the cool. I did replace the stock fan with a Noctua NF-P12 to match the overall silence in my silent build.

Comment:
high quality heatsink for a low price. nothing much else can be said. works much better than most heatsinks and a lot better than stock. comes with an extra clip if u want to run a push pull.

Comment:
Really good purchase to cool down my i5 760. I will be able to overclock my CPU easily to 4Ghz at a very low cost.

Comment:
I got 2 of theses to replace extremely loud AMD stock cooler. Not I have cooler temperatures and a near silent heatsink fan. I have not tested them on Intel systems(Intel's stock is not THAT loud) yet, but i would bet they work just as well there. This is unbeatable for the price

Comment:
Amazing replacement for any stock heatsinks, it lowered my cpu core by 10+ degrees compared to the cheap old one I had. Improved airflow after installing it to blow out air through the back. It did block a NB cooler I was planning on using because this thing is huge so had to re-adjust.

Comment:
This is probably still the best cooler from a price to performance ratio. Keeps my I5 750 OC'd to 3.6GHZ with no temperature issues.

Comment:
I have been using the stock heatsink included with my intel core 2 duo for almost 2 years.Installation was a little cumbersome but not impossible by no means. Since this supports a large range of socket sizes, mounting system isn't obvious to install.Once installed though, I noticed a 10C decrease to the stock cooler (using the included fan) under both load and idle temps.With my new amazing temperatures I decided to OC my CPU (e8400 to 4ghz) with awesome temps. 31C idle, 53C load.I am really happy with this purchase and would recommend this to anyone who is still using the stock heatsink.

Comment:
Excellent heatsink for the money. The temperatures are just as low, if not lower, than my old Scythe Ninja. One major advantage of this is the mounting which is easy and firm. The mounting is cleverly designed so all sockets can use it. I can't say anything bad about it really. As long as it fits your case, get it by all means. It's weird that sometimes this thing goes back order for some reason...

Comment:
All in all a very worthy and cost effective cooling solution for all sorts of processors. The value of this cooler is second to none, other more expensive coolers offer minuscule advantages in the range of 3-4 degrees for triple the cost.

Comment:
Don't let the cons I've listed detour you from this heatsink, it is definitely the best price for performance you will get. It comes with pieces so you can mount another fan for a push/pull configuration which will improve temperatures even more.The only thing I must say is to make sure it fits in your case before you buy it as it can be took big for some cases.

Comment:
I am amazed. Currently useing asus m4a785t-m with a athlon 2 x2 250. 3.6ghz prime stable, and this thing cut my load temperature down from mid 40's on stock cooler, down to 27c. This cooler is astounding for $29.also, I'm useing 2x2gb of gskill ripjaws 1600mhz ddr3, and the fan on the cooler does not block the first ram slot. Very happy.

Comment:
highly recommended.. best bang for the buck.i'm running an i7 930, stock cooler was a POS, 50C idle; 100C load. after installing the hyper, im now at 35C idle; 75C full load.

Comment:
Install was very easy and even if you are not an overclocker (which I am), this is a very good product to buy.I have idle temp at around 30C and load at 43C, and huge difference between this heatsink and intel stock heatsink.

Comment:
Due to it's size, one of my ram slots are blocked. Also, in my antec 1200, there us approx 1 cm to spare in height.As with all heat sinks, MEASURE YOUR CASE!At stock speeds, my idle temps went from 45 to 25. Load temps went from 65 to 40. (temps are with a single fan)I was expecting less performance, and was very pleased!I highly recommend this product to all!

Comment:
Got this for my Intel Xeon x3440 Quad core processor. I haven't overclock my cpu yet so I can't tell how much temp will it keep down compare to the stock speed. It is huge so make sure your case has enough room for it.

Comment:
Great Heatsink for the price. Come with a backplate to help the motherboard. Heatsink is Heavy and Huge, be sure you have enough room inside your case for it before buying. Fits perfectly in a Antec 900 Case.

Comment:
I bought this for my X6 1055T and I was amazed that by going from 2.8 to 3.8Ghz my cpu only went 11C higher on load and it's still dead silent. One suggestion I can tell you is to install it THEN mount the fans, otherwise it will be a huge PITA. I could get a second high quality fan for the same price of the regular price of this heatsink since it's so cheap when price-matched. It's performance are even the same as the products like Corsair H50 which cost 3x more so look nowhere else!

Comment:
The instructions that come with this cooler leave a lot to the imagination. I suggest reading reviews on how to most effectively apply the thermal paste to this cooler and make sure you do a dry test fit before putting the paste on and bolting it down. Other than the intruction manual being poor, the product is amazing. Got an extra 100mhz OC on my Phenom II X2 550 and lowered the load temps by 16C over the stock cooler. Also quieter than the stock fan.

Comment:
super priced cooler that everyone should consider buying even if they never plan on OC'ing their CPU. This is so much better for such a cheap price. coolermaster hit the nail on the head with this one in terms of performance and price, and now reap the benefits of legions of fans!

Comment:
Lowered the temperature of my i3 530 from 35C to 22C on idle.It's also quieter than stock fan when idling at 1000-1200rpm.The only problem is that I can't close the side panel because the copper pins are too long. So be careful, it's a little higher than 120mm.

Comment:
Installed this with a Gigabyte UD3P in an Antec P180b Fit good no issues and blows thru to the top case fanI previusly used an Arctic Freezer Pro push pinner Hyper is way better results..yes you have to remove the motherboard to install the rear bracket but it is worth it!!

Comment:
I wanted a heatsink that could cool the CPU efficiently without spending an arm and a leg to buy. This had been a good purchase for me. Even though the idle temp is 40C, it's running very cool 43C at load. I recommend this cooler if you are looking for a cooling solution without breaking the bank, but make sure you find the installation video so you won't be frustrated by the included instructions.