G.SKILL F3-10666CL7D-8GBRH Ripjaws PC3-10666 8GB 2X4GB DDR3-1333 CL7-7-7-21 1.5V Memory Kit

Comment:
Effortless to install, uncomplicated to configure none My initially build in more than ten years. This RAm is an inexpensive way to make all my computer software perform faster and get work accomplished in less time. No challenge finding it to run at advertised ratings, with ASUS MB and AMD quad core 955.

Comment:
I installed, set BIOS CAS timings to 7-7-7-21 (not default) and it worked without a hitch. I didn't have any of the issues other posters have talked about. Windows index provides it a 7.7 out of 7.9. None so far None

Comment:
Fantastic stuff, runs at spec None so far actually glad about this, comparable to 1600 @ cas 8

Comment:
excellent performance, rock solid at stated voltage and timings. that I didn't buy more. went with these sticks following 1600's from one more manufacturer wouldn't run stably with my AMD 1090t. One week now with no crashes so far. Required to set the latency settings manually in the BIOS *not a con, just a note*.Rig: Gigabyte GA-890GPA-UD3H rev2. Bios FF, AMD 1090Tbe, GSkill 2X4GB cl7 ddr3 1333 (F3-10666CL7D-8GBRH), ATI 5570’s (X2 in crossfire), 320 GB WD caviar blue OS drive, 1 TB WD caviar black information drive, 800W Apevia psu. All settings default except latencies.

Comment:
These were a snap to setup with my Asus P9P67 Pro, just set the XMP profile and they work perfectly. Tested fine. Haven't tried overclocking them but I have no need, the computer system is smokin fast. Cas latency 7, what more do you need to have. In channel A1, the heatsinks rest against the side of my Hyper 212+ fan. Just moved to channel B. I'd purchase these again. I've observed individuals reporting concerns with DDR3 1600 on P67 Pro, but these 1333 sticks have no matter.

Comment:
Preforms well with a MSI 890FXA-GD65 motherboard.Timings are as advertised on this board with no modification.Runs cool with no airflow from the CPU HSF mainly because I am using a sealed water cooler on the CPU. No cons so far, have tested with multiple operating systems, virtual machines, and even used it as a ram disk with no errors or crashes of any sort. G.Skill is a brand I was skeptical of at initially but it has genuinely earned a reputation for good memory. Ramdisk tests revealed among two.6GB/s and four.2GB/s reads and writes.

Comment:
Functions well. Wonderful value for 8GB. Shipped fast. Advertised as 1333 with a Cas latancy of 7. Will only run at a Cas 9 for 1333 mhz. I get a Cas latancy of 7 when I bump down to a 1066 speed. When I ordered this I thought I would be obtaining a Cas latancyof 7 running at 1333. This is missleading. I've been caught up with a different conditions like this. Works with my gigabyte mobo. 890FXA UD5. Even although its not precisely what I wanted I will almost certainly just keep it so I don't have to mess with a return. Manufacturer Response:.Dear ConsumerThank you for your G.Ability purchase and evaluation. We are sorry to hear the memory is not operating to specification. This kit need to have no dilemma with DDR3-1333 7-7-7-21 1.50V. If you think it is not capable of that spec, please really feel free of charge to send it in for RMA. All G.Ability memory packages are backed by a lifetime for these sorts of circumstances. If the memory does not operate to spec at any time, we can have them replaced with new ones that will. Thank youGSKILL HelpGood quality and buyer service are our best priorities.Tech Help E-mail: ustech@gskillusa.comRMA Dept Email: rma@gskillusa.comG.Ability Forum: http://www.gskill.us/forum/

Comment:
Memory runs as advertised 7-7-7-21...I had them in a MSI 890fxa-gd65(JUNK) they were compatible with that mobo till it died in three-four days & went back to Newegg.Now i have them in a Asrock 890fx deluxe4 operating good!! Gonna try & overclock them soon. Worth the added maybe ฮ bucks for the much better speed/latency of 1333 ram NONe!!! Compatible in two mobo's so far..MSI 890(junk) & Asrock 890 Not to tall,fit with aftermarket heatsink/cooler on my AMD 1100TGonna get a different 8ghz soon!! Nice job G.Skill!!

Comment:
Worked fantastic for small over a month and but. see cons.Tight timingsFantastic response. I started to get random reboots and freezing for no reason. Dropped the timing and gets greater, dropped the timing to 1000 from 1333 and is stable with cas 6. Sad that it looks as the RMA method is going to be a discomfort. -sigh- Manufacturer Response:.Dear ClientThank you for your G.Skill invest in and assessment. We are sorry to hear 1 module is causing troubles. We can surely have it replaced to get your program up and operating smoothly. The NewEgg and G.Skill RMA method is fast and painless. There is no hassle at all, so you can simply send them in and receive replacements shortly. Must you need to have any additional assistance, please feel free to make contact with us directly. Thank youGSKILL SupportExcellent and customer service are our leading priorities.Tech Support E-mail: ustech@gskillusa.comRMA Dept Email: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
Functions 100% at 7-7-7-21 on a ASUS PH67M-LE version 3. and also the original board. Nonetheless there are a quantity of extra memory settings in the BIOS that aren't specified.... The default timings were incredibly confusing, I had to manually adjust them to the higher performance settings. The memory timings are very confusing. SIW reports 9-9-9-25-34ﲯ.five, CPU-Z 7-8-8-8-29, neither of these are the G-Ability Spec..... Windows Encounter is broken - I have an 8 gb installation on Win7 -32 bit. I only get five.5 on the memory timings.... My E6600 at the similar clock rate got 6.three.

Comment:
The stick that wasn't defective works fantastic. The other stick froze up my pc and produced me sad. Manufacturer Response:.Dear CustomerWe are sorry to hear one module is not operating effectively. Please send it in for RMA and the replacements really should perform considerably better. All G.Skill memory packages are backed by a lifetime guarantee for these forms of circumstances. If for whatever reason your memory is dead on arrival or becomes defective soon after a couple days, weeks, or years of use, we will exchange it with a new replacement without having question. If you have any additional concerns or matters, please really feel cost-free to speak to us directly and we will be glad to assist you.Thank youGSKILL AssistanceTop quality and customer service are our prime priorities.Tech Help Email: ustech@gskillusa.comRMA Dept E mail: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
works in program none item was as stated and worked with the program. no problems. Manufacturer Response:.Dear CustomerThank you for your G.Skill obtain and evaluation. Glad to hear this memory kit is operating nicely in your method. If configured effectively in BIOS, the low latency ought to have incredibly great efficiency outcomes. This is our ideal kit without having overclocking, and it is 8GB, so it is 1 of our most well-known kits. Ought to you have any future concerns or problems, please feel free to get in touch with us directly. Thank youGSKILL AssistanceExcellent and consumer service are our best priorities.Tech Help E mail: ustech@gskillusa.comRMA Dept E mail: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
Very good value & reputation. Low latency. SPD says it's 1066MHz. Have to manually set clock speed. This is my 1st PC create in 20 years, so I'm not up on all the most current hardware. I wanted 1333MHz RAM to go with the max rating of my MB & processor, but I accidentally ordered 1066 instead. I noticed the mistake just before opening the package, so I returned it (ึ) and ordered the 1333 (ุ a lot more than the 1066). The package for the new RAM says 1333, but the SPD says 1066. I set my clock to 1333 and all is fine, but I wonder what I got for my ๠. Printing on a package?BTW, I'm more than 40 and not as sharp as I once was, but I can't be the initially one to confuse PC3-10666 with 1066MHz PC3. Don't make the exact same mistake. Manufacturer Response:.Dear CustomerThank you for your G.Skill purchase and evaluation. Glad to hear the memory is operating properly. If you have a plan like CPU-z, appear in the SPD timings table. The furthest correct table really should show 667MHz 7-7-7-21 1.50V. To be certain you got what you paid for, this memory need to be capable of the rated specifications above. You could have basically misread the SPD facts because there are multiple tables. If you have any additional concerns or difficulties, please don't hesitate to get in touch with us directly.Thank youGSKILL AssistanceHigh quality and client service are our top priorities.Tech Support Email: ustech@gskillusa.comRMA Dept Email: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
Not an isue with this 2x4 kit at all.What a lot more could you ask fo.Running great in my Asus m4n98td-evo motherboard.Operating at factory specs. None.

Comment:
Worked/Compatible appropriate off the bat with my new ASUS P67 board. It has far more than adequate capacity and speed to last my mid-high finish gaming rig for the subsequent four-5 years. Like I had read in other views, make certain to check the BIOS for the memory Latency. The default Latency will show as 9-9-9-24. Not seriously a Con, just something I may possibly not have noticed if I didn't read up on the critiques. I run my gaming rig with zero to small overclocking, the 1333 speed is easily enough to preserve every thing operating particularly quickly, and I don't believe the 1600 + speed sticks are worth spending the extra money on unless you just have a lot of spare money to spend.

Comment:
Very quick RAM. I have it O.C. to 2000mHz and its stable. None

Comment:
Not several pros here. It looks cool. Didn't ship quickly. Worked for a small even though, but immediately after having my method up and operating less than 1 month, and getting several BSOD's I ran Memtest 86 and identified that both sticks were faulty. I dunno how nicely this is going to work. With 2 out of two sticks faulty already I'm a bit nervous about the next set. Shipping was slower than I have ever had from newegg. Took off 2 eggs due to 2 faulty sticks, and 1 for the shipping. Shipped from DHL.. what a joke. Looks like G-skill is going downhill. I had no problems with them in the past. As someone else mentioned "what happened to high quality manage?" Manufacturer Response:.Dear ConsumerWe are sorry to hear you received negative modules. This really should in no way occur. However after the memory leaves our factory, we have no manage over handling. If you RMA the memory directly by way of us, we can guarantee a perfectly working kit. Need to you have any further concerns or concerns, please really feel no cost to contact us directly. Thank youGSKILL SupportExcellent and consumer service are our best priorities.Tech Support E-mail: ustech@gskillusa.comRMA Dept E-mail: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
Looks good. Updated evaluation:It will not run reliably at the rated Timing of 7-7-7-21 on a new GIGABYTE GA-H67A-UD3H-B3 motherboard with an Intel i5-2500K.When installed in my very first GIGABYTE GA-H67A-UD3H motherboard, bios F5 it would freeze or reboot about when a week, with bios F8 or F9 it crashed everyday when the timing is set to 7-7-7-21.For now the GIGABYTE GA-H67A-UD3H-B3 motherboard and bios F2 and the timing on AUTO, it's running OK with a setting of 9-9-9-24 and it is stable for now.I known as newegg to see if I could exchange it for G.SKILL Ripjaws X Series 8GB Model F3-10666CL7D-8GBXH.I was told no mainly because it is now past 30 days. I didn't get what I paid for but it's usable. Manufacturer Response:.Dear ConsumerWe are sorry to hear you are getting problems. If you think there is a challenge with the memory, please really feel free of charge to send it in to us directly for RMA exchange. We will be far more than glad to send you a new kit that may possibly perform far better. In addition, our technical support department is readily accessible to aid you, so please don't hesitate to request assistance. Thank youGSKILL AssistanceQuality and client service are our top priorities.Tech Support E-mail: ustech@gskillusa.comRMA Dept E-mail: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
I installed, memory registered as advertised and almost everything was A.O.K.Memory that is a good price for the perfomace. I haven't attempted to OC because this is my initially develop and I dont want to BSOD myself before I can in fact use my PC. I will be searching to obtain one more 8GB soon, even although I dont truly will need it, I am already tired of looking at the empty DIMM slots on my M/B by way of the side panel on my case although. ;) I am not educated sufficient to supply any cons to the newegg clients. this is my initial try to create a PC. I wish AMD would support triple thread technology Part of my 1st Develop:AMD Phenom II X6 1090T Black Edition Thuban 3.2GHzASUS VH242H Black 23.6" 5ms HDMI Full 1080P Widescreen LCD MonitorThermaltake Armor A90 Black SteelASRock 870 EXTREME3 AM3 AMD 870 SATA 6Gb/s USB 3. ATX AMD MotherboardG.SKILL Ripjaws Series 8GB ƒ x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666)XFX HD-567X-ZNF3 Radeon HD 5670 Windows 7 Ultimate Full OEMIntel X25-V SSDSA2MP040G2R5 2.five" 40GB SATA II MLC SSDWestern Digital Caviar Black WD1002FAEX 1TB 7200 RPM 64MB Cache SATA 6.0Gb/s 3.five" Internal Difficult Drive -Bare DriveSaitek Eclipse II Backlit Keyboard5600 dpi Cyborg R.A.T. 7 Gaming Mouse2x LITE-ON Black 24ቴኌ DVD Burners Manufacturer Response:.Dear ClientThank you for your G.Skill obtain and assessment. Glad to hear this memory is operating properly in your system. This is a really good performance kit for AMD platforms. The low latency is best for gaming as it provides quicker in and outs. Though the frequency is not high, it is adequate and does not stress the memory controller. If you have any future questions or difficulties, please don't hesitate to contact us directly.Thank youGSKILL AssistanceGood quality and consumer service are our leading priorities.Tech Assistance Email: ustech@gskillusa.comRMA Dept Email: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
It was on the list of advised memory for my Gigabyte GA-H67A-UD3H mother board. It works as it need to. none

Comment:
Does what it claims Ɨ-7-7-21) no difficulties. $$ was good. I'm pleased. Free of charge beer not included. Not so happy about this. 1090t black @ 3.8 on MSI NF980-G65

Comment:
I don't see any Pros yet, taking into consideration this is the second kit I've gotten, and it also fails memtest 86 tests with thousands of errors. two Bunk kits so far, and I'm about ready to just get my dollars back if possible Manufacturer Response:.Dear ConsumerWe apologize for the inconvenience. You really should not have such problems. Please make confident to allow XMP (Extreme Memory Profile) or manually input the memory settings in BIOS. Also, check to see if you have the newest BIOS for the motherboard. If you continue to have problems, please feel cost-free to contact us directly for help. We can help troubleshoot and make positive the memory is the culprit. It is rare for two kits to be poor.Thank youGSKILL SUPPORTExcellent and customer service are our leading priorities.Tech Support E-mail: ustech@gskillusa.comRMA Dept Email: rma@gskillusa.comG.Skill Forum: http://www.gskill.us/forum/

Comment:
* Rapidly* Cheap* Reliable None FYI, I had to update my UEFI firmware on my Asus P8P67 PRO motherboard in order for 16GB of RAM to show up. This is NOT a issue with the Gskill memory, but just a FYI for you PC builders out there :)

Comment:
Low cas latency Ɨ) and incredibly fast stock timingsƗ-7-7-21). Installed them on an ASUS P7P55D PRO (i5 760) with no troubles. I did have to manually set the timings although (but that's fairly usual). None. Chose G.Skill because of their wonderful warranty and customer service.

Comment:
Have been running these at 1600 in a Ta90fxe biostar mobo for 45 days no hiccups. OC a three.5 AMD deneb to 4.7 and these are keeping pace. No cons No temperature issues at all the heatsinks on these are not just for show.