LOGISYS Computer CS206BK Black Computer SOHO Case

Comment:
It looks decent. It works.Space for extra 120mm in the front, 80mm fan on the side panel, 80ኸmm fan in the rear.Tons of airflow (at the price of noise).Thumb screws for the side panel.No sharp edges that I noticed. PSU: Only 16A on the 12V line. Fan is very loud. Only 330W in reality.Case: Flimsy panels. One open slot cover in the back. Hard to take out the I/O panel. New I/O panel doesn't fit solidly. Only a single included fan 80mm, when there is a slot for 92mm fan. Empty 80mm fan spot on side panel looks unpolished. You can take out rear slots for expansion cards, but there is no way to replace them if you make a decision to take away the expansion card later. 5.25 bay doesn't fit snug about the optical drive. You can see spacing on the sides. Along with that, the screws to tie in the optical drive are left to reach into the screwholes of the drive. Tough drive installation was troublesome. On the back side, you can only use little screws mainly because the horizonal opening for the screw isn't lengthy adequate? On the front side, you had to use a different thicker thread screw mainly because the same screws you applied on the back side would just fall throw the screw holes getting too little. Odd number of included screws, no washers. Running out space to write into the cons and I had much more to say. No case speakers. And so on. Just in common, items don't fit in the case exactly. They're not far off, but you have to perform to make it fit ideal.I have a Lian-Li PC65 case, and the traditional Antec Sonata case that I worked on previously to base my encounter on.

Comment:
Cheap, easy, solid. Lots of five.25" bays and additional fan slots. Maintaining my gf's x2 550 technique cool and as quiet as you can expect for 80mm fans and a cheapo situation. It's been a couple of months and the power supply hasn't died. No annoying LED's to make you believe space ships are landing in your workplace. It's a small noisy, which is to be expected from a lower finish situation. That, and it's a little bit of a dust magnet. phenom x2 550 II BE @ x3 three.six on stock fan idles about 40 in this small guy with a 4670. Properly worth it if you're developing a budget machine. I wouldn't put significantly faith in bob's power provide but if you're spending less than 50 bucks for a situation/psu supply combo you can either anticipate it to last three days or to infinity. It'll at least give you a small bit of a buffer to shake the money tree just before you have to replace it.

Comment:
clean, did the job none You get what you pay for so dont assume this is a gaming tower. I create Comps for new Users and it functions one hundred%, purchase this for 31 dollars and you get a 31 dollar tower.

Comment:
Does the job and consists of PSU. Flimsy and out of square. Material not very metal not fairly plastic. Plastimetal? Metaplastic? It's strange stuff. For my wife, she doesn't mind. I am just being picky.

Comment:
Inexpensive. Has energy provide. Has fan. Free fast shipping. Genuinely light for a steel case. Appears like they just slapped it with each other with tiny care. Energy provide loosely mounted and bent, front panel broken in 3 areas and misc. dents and scratches all more than situation. Possibly left more than components at logisys and put with each other to get rid of inventory. Purchase it if you can afford to lose ฮ.00 or just require a low-cost situation.

Comment:
Case is solid, with lots of room for components and drives. The power provide is junk. The specs for the case and the energy provide (which can be bought separately) erroneously state that this is a 480W power provide. Even so, the markings on the power supply itself show this to be a 330W power supply. I paid a bit additional than I would have for just a case without a energy supply, and had I known that the energy supply was genuinely only 330W, I would have just got a standalone case. If you're seeking to energy anything more than a couple drives on a single-core machine, look for a diverse case. I've got a quad core that I've been slowly adding to over the past two months, and when I added a fourth drive Ɠ HDD, 1 DVD Drive) to this machine, almost everything started to go haywire. I'll be purchasing a new PSU nowadays.

Comment:
< Its low-cost. < You can place a personal computer in it. < If all else fails it'd make a fantastic pinata at an LAN celebration. < Its low-cost. < Reminds me of these bogus props they used in 60's westerns that disintegrated throughout the saloon brawls. Got this as portion of a spending budget package from a Newegg competitor. I've upgraded the graphics, PSU (Coolermaster Extreme 500W) and replaced the noisy, inefficient 80mm rear exhaust fan with a 92mm Antec Smartcool and installed a Rocketfish 120mm intake @ 1200 rpm up front. Front fan doesn't draw air as a lot as you'd like due to poor situation style but my mods have improved the flow and cooled the GPU considerably.The preceding reviewers aren't exaggerating about the flimsiness of this case. Extreme care should be taken while operating on this unit as it is created from genuinely light supplies. I've had the front panel off twice and have basically had to rebuild it.This case looks fairly sharp and with care must serve my requirements needs for some time but I couldn't possibly advise it to any individual making a new program.

Comment:
Adequate connectors, great price, includes PSU and fan, enough bays. Feels cheapie-deapie, looks a tiny like it's from an 80's Sci-Fi film (bright blue/purple LED with shiny black pastic) power switch feels low-cost and doesn't truly line up, only comes with just enough screws to put it together install 2 cards, and two drives. The large one particular even though: there are two SATA power connectors on the identical lead, but they are genuinely close together, so unless you get a different SATA power lead, you require to place the HD kind of high up, and the optical drive actually low down. No directions, and absolutely nothing on the internet site. Fan from time to time shorts out. It's a excellent price tag. It comes with anything you want and absolutely nothing you don't. This was my 1st construct, so instructions would have been useful. There are no cable guides, as far as I can tell, so I have some twist-ties holding cables out of the way. In retrospect, I most likely would have spent yet another บ-20 to get a superior case, but truly, the situation just sits on my floor. I'm not gonna travel about the country with it, so it's sturdy enough to get the job accomplished. It's not silent, but it is whisper-quiet. I consider I may possibly replace the rear fan, add a side fan, and possibly get a SATAǚ-pin adapter so I can move the drives.

Comment:
Cheap... Incredibly thin metal. Poor motherboard and power provide support. Purchased four, three out of 4 damaged in shipping two were wrong color.

Comment:
good searching excellent for micro atx board 480w PSU restricted plugs for Motherboard no 4x2 if your pcie card necessarypower your out of luck, tight fit for ATX board and the power button is fully invisible day or night Fantastic for a inexpensive create

Comment:
Affordable case, efficient and high PSW. Flimsy metal but it's low cost. Have not had one particular PSU fail on me but! I've been developing systems with this for pretty much a year. They got much better over time even so the shipping still needs to be worked on. Pretty much every single ten circumstances I either get a dinged case or its scratched or incredibly messed up. Also they have felt the will need to not contain the method board speaker any longer. I need to have this and if they don't put it back in I will have to go with one more case when I discover one particular. I have bought over 100 so please include a speaker!!!! Also make the DVD drives fit correctly please, tired of the gap in between the drive and the tower.So Recap:Shipping HarmTechnique SpeakerDVD Dive Correct Fit Rated 4 stars as I want a speaker

Comment:
These situations can be nice hunting and work effectively for the cost. I have purchased dozens of these from Newegg and from all more than the internet for nicely more than a year and up till about the last 8 weeks they have worked nicely for me but that has changed.Out of the last ten that I have purcased I have been in a position to use four.I just recieved three from Newegg and two of them have broken front panels and another that I had opened last week looked like it has been in a factory unboxed for months scratched up and dusty.If I had to guess Logisys is either going to discontinue this situation and are selling off all the leftovers they can find broken or not or they are receiving tricky up for cash and have no high quality manage what so ever.They also have no consumer service dont bother with that just thank your lucky stars for Newegg standing by what they sell.Wait a although if you like this situation to see if the dates of the poor reviews get older displaying that the bad situations are all gone and hopefully they dont put them back into rotation to sell once again mainly because 35% of the time folks dont RMA Thank You Newegg for standing behind what you sell!!

Comment:
A nice easy case, doesn't bring focus to itself. Had space for almost everything and plenty to spare. The rear fan appears higher excellent than I expected.The PSU functions just fine, and despite the fact that it is a little louder than I expected, I don't notice it unless I am trying to notice it. Part of the plastic front was broken when it arrived: the bottom of the CD/DVD trays on the proper side.A small bit of krazy glue and you almost can't tell that something happened.The sides remind me of cookie sheets, they bend a small rather than staying rigid. AMD Athlon II X2 250 three. GhzA-Information 2x2GB DDR3 1333Biostar GeForce 9500 GT 512 MB 128-bit GDDR3ASRock M3A770DE AM3WD Caviar 320 GB 7200 RPM SataLogisys CS206BK Mid ATX Tower Case 480 Watt PS

Comment:
The case itself has a good, understated appear to it. Just a plain, smooth seeking black case that isn't "in your face". The steel was rolled, so no sharp edges. Its thin, but not anyplace as thin as most sub 30 dollar circumstances are. It doesn't really feel like tin, but its no Thermaltake or Antec either. Its also 30 bucks.....Capability to add a 120mm front, 92mm rear and 80mm side is a plus if you have a lot of high heat componentsI place in a mico atx board and a front 120mm fan (which is a pain to place in, BTW) and have had zero troubles. PSU worked fine for me, but its loud as hell. It moves a ton of air, but it SOUNDS like it moves a ton of air. Front LED glows blue when its on, wish it didn't, but that's just a personal preference. The only purpose its not getting 5 stars is mainly becauseɅ) the PSU included is loud and, truthfully, in all probability pretty terrible.two) the cd bays are a little wider inside the case that the drive you are mounting. This makes screwing it with each other feasible, but additional time consuming than it desires to be. This could just be my case, on the other hand. I'm confident dimensions are off 1-2mm from time to time. I added the front 120 with three pin connection, added an antec 380 green power PSU and a athlon II X2 240. I put some cheap foam on the inside of the door and on the bottom of the case (check out hobby lobby or anything)Its now so quiet that I cant hear it operating unless im kneeling by it with my ear to the PSU fan.

Comment:
Low cost (อ.99). Come with a power supply. Unless you are creating a power hungry process, this PS is sufficient. It appears decent! Spacious if you need to have to install numerous devices. Two fans (front and back) are also included. In brief, this case consists of all the products needed to create a process. Very flimsy! Not all components are connected as they should be. You can see some holes that need to be mounted to other components, but the factory forgot to mount them. The 1 I got has at least five locations will need to be fixed, which I fixed them with my personal screws and nuts. The main challenge I have with this case is that the portion help power supply is bended when I got it and a single of the component on the suitable corner is not mounted correctly. This makes the energy provide appears shaky. Again, I will need to fix it myself. Energy supply is incredibly light. You possibly don't wanna have this a single to be your major power source.For some cause, they don't include adequate screws and jumpers in the package. I need to have to locate a couple of them just before I can create a system. Overall, the design of the case is great. Immediately after putting almost everything together, it is fantastic. Nevertheless, LOGISYS requirements to stop working with the factory who tends to make the case. The fabrication is truly terrible!!!If you require to buy a low cost case with enough area, this is a great purchase. Even so, you'll will need to take care of some small defects.

Comment:
It holds all my elements. Lots of areas for airflow. Power provide dead soon after 3 months (luckily I had planned on replacing it anyway). The mount for the power supply is the worst I have noticed in 9 unique case models I have utilised, can't assistance the new powersupply's weight when standing upright so the powersupply dips down and hits the HSF of the cpu. Negative design. You get what you pay for but this is not worth what I paid and that's why it gets 2 eggs. The case is Extremely smaller inside, had to use stock heatsink due to the fact second a single I had was too tall to fit.

Comment:
This is an update assessment. 1st assessment i gave three eggs and listed largely faults. I was able to super glue broken front panel pieces and got laptop up and running. It is particularly quiet and I added a front 120 mm fan and appears quiet and cool. Power supply operating fine and case looks fantastic. Is a light case which I like. Truly only point I can't operate about is length of SATA connector. Can't place DVD drive on top slot of case and have Challenging Drive in 1 of the bottom slots where it belongs. Will have to put DVD drive on bottom five" slot. This may possibly lead to some men and women not to get. Don't acquire for a top of line construct but functions for budget or mid range computer.

Comment:
-Cheap, affordable pricing.-Contains Power supply.-Finishing on the case is decently appealing.-Somewhat sturdy panels.-Front blue LED's. -Back portion is fairly flimsy, I removed the I/O paneling in the back to use my mobo's bracket, it seemed like you shouldn't be in a position to do that but the metal was really flimsy.-Can't comment on the included power supply due to the fact I bought/used yet another 1. But excellent for a backup I suppose. Acquire this case if you can't afford a fantastic one particular, but you get what you spend for, still it's not all THAT bad if you aren't going to be tinkering with it generally.Also I didn't seem to have any wiring difficulties as other individuals reported in evaluations, but I have yet to really test it on a operating Pc, but my headphones make a slight electronic buzz noise when I turn on the motherboard which really should mean it functions. Also the rear fan was not DOA.

Comment:
Affordable. Comes with power supply. Case feels like it is made from nothing at all additional than a handful of layers of tin foil. The pins on the molex connectors were so loose that they fell out of their housings. Case was warped and very flimsy. This would be a decent choice if you are putting together a budget system that is going to remain in one particular location. Anything outside of that, I would suggest a unique case.

Comment:
quite low-cost, you get what you spend for..... extremely flimsy, front was broken. power provide buzzed rather loudly..

Comment:
Low cost Lots, Incredibly low-cost construction, I purchased 3 of these for custom builds, the gage of steel utilised is thinner than a pop can, Went to install the Mother Board and the stand offs exactly where to lengthy, I think about its in fact the Mother Board tray’s fabrication is incorrect since the stand offs seem to be regular 6mm, Had to take a dermal to 18 brass stand offs (Not Fun) after tweaking the case numerous times for fit 1 of them had a led out further investigation revealed a lead to the resistor for the led was left unsoldered. If I didn’t need these immediately I would have returned them, I hope the power supplies don’t go negative…

Comment:
fit and finish on case is extremely nice for the spending budget case put a 120 fan in front 92 on rear and 80 on side nice airflow able to run e5200ʃ.43 prime stable with 9600gso also overclocked from 580몸 to 650񲿘 fantastic for a spending budget gamer no voltage spikes on energy provide at full load pressure testing 330 constant load mobo stand off holes strip out with little force absolutely nothing a drop of xxxtite or glue wont repair let set for 30 min. and continue with develop back plate is difficult to eliminate but less complicated if you commence in leading left corner and work metal back and forth from there hammer and chisel not needed for me it is in very good though bent side panel retaining clips in a small with fingers for much better fit and finish and quiteness quite superior case and energy provide for the cost

Comment:
-Price tag: if you want to devote $ on parts, not case, you could do worse- looks fantastic: not a ton of gaudy lights and junk like that. It does it's job and looks great in all black.- Easy assembly: thumbscrews are great, easy set-up -THE POWER Provide: it is a fairly good wattage for coming with the case, but what a piece of trash. It has no 6-pin pci-e connector (which it fails to tell you on the specs sheet) so for most pc builders (and all gaming builders) it is pretty useless. Also, the sata power cords were not lengthy adequate to have the dvd/rw drive in the best slot, though nonetheless connecting to my hdd.- flimsy: the metal is thin, and the side panels will warp if you are not cautious.- The i/o panel is a super discomfort in the rear to pull out. I ended up needing my leatherman to remove it All in all, it's not too bad for the dollars. I employed it to construct a SCII rig for a buddy of mine, and it works fine, minus a couple headaches triggered by the psu.I didn't want to have to get a new power supply, so i ended up Frankenstein-ing a 6=pin connector from 2 of the four-pin connectors and some electrical tape. Works fine, but definitely a hassle.Decent case for a penny pincher like myself, but subsequent time i would invest the ten bucks and get something a lot more sturdy.

Comment:
no pros as it didnt operate for me. this doesnt have four pin 12V ATX cable.

Comment:
constructed properly for a low-cost case, not supper flimsy like some at this value range. The power supply works well, I purchased a second as soon as I saw how nice this case was.for the price tag this can't be beat. none at this time The metal is better than most with this case.. make positive you have a tin snip or a thing to get the motherboard plate off.