GELID Solutions 350 mm PWM Y Cable

Comment:
It's a splitter. The cables are wrapped and it feels strong overall. It didn't come with two of them. Performs.

Comment:
great item none yet another issue you might have to do is switch the wire positions on a 3 pin fan for it to operate, considering that it was desined for a four pin conector. all you have to do is see which is the power wires and pull the pins out and reinsert them in there suitable positions, you do this to the fan not this cable its esy i do this all the time

Comment:
This cable is excellent for what you need to use it for. There are no flaws and it operates fantastic. It is 13 inches extended, so you will have enough cable length in my opinion for what you need to use it for. It is also sleeved with Black Techflex cable sleeving. You could also obtain far more of these cables and connect them collectively, so you can connect up to five PWM fans (such as the GELID fans I posted in other thoughts that I use). This cable is great, there are no cons. I use this cable with these fans by GELID. Read my assessment on these fans, they're the very best fans I have ever purchased and beat every other fan out there in my opinion, such as Scythe.The fans I use:http://www.newegg.com/Product/Product.aspx?Item=N82E16835426025&cm_re=gelid-_-35-426-025-_-ProductIf you're thinking about purchasing this cable or the fans above, don't hesitate, buy it. There are also Blue LED fans by GELID.

Comment:
Functions. None. 4 pin Y-cable, but only correct PWM fan manage Ɣ pin) to 1 branch. Other branch is 3 pin.

Comment:
Functions as it was designed. It is expected that four-wire PWM fans are attached to this cable and the cable is attached to a 4-wire mobo header. This permits PWM manage of both fans. Only the tach/sense line from *one* fan should be used to ensure the appropriate RPM is monitored (one fan provides the tach speed, the PWM regulation is applied to each fans). Naturally you should use the exact same fans (brand and model) for both fans to guarantee the PWM duty (pulse width) final results in the identical RPM for each fans in a push-pull configuration, like across a CPU heatsink. Different fans could be utilized, like one for CPU and yet another for rear exhaust, without having concern that they specifically match on RPM. Wish they supplied (at Newegg) some shorter versions. 350mm ྭ.8 inches) can be a tad extended when utilized for push-pull fan config about a CPU heatsink when the CPU mobo header is right there by the CPU. Have to coil this up and use wire ties to keep neat. Be positive to use 4-wire fans on every single end. A 3-wire fan on the three-pin connector would only get gnd and pwr and so it would spin at full speed. You want the PWM line to a 4-wire fan to use PWM to regulate the fan's speed. I can't believe the noobs that complain that 1 male end only has three pins. Regardless of their rantings, it is still a four-pin connector with 1 pin missing - and that pins Should be missing. The thought is to use the tach/sense from One fan but use the PWM (pin four) for both fans - so they are synchronized to spin at the Same speed. What use would it be to have 1 fan be regulated while the other spins at complete speed? You certainly don't need to have this cable for that.Tach/sense functions by sending two pulses from the fan for every single 1 rotation. If the sense from 2 fans exactly where sent to the mobo then it could see up to twice the number of pulses with the outcome the fans would spin at half the expected RPM. You use the PWM signal with four-wire fans to regulate their speed. Just goes to display that those who complained about 1 pin missing from a 4-pin connector don't know how PWM fans operate, how the sense signal is used, and don't comprehend they seriously need to have to use four-wire PWM fans on every single finish of this splitter.

Comment:
Applied for adding second fan on to - COOLER MASTER Hyper TX3 RR-910-HTX3-G1 "Heatpipe Direct Get in touch with" 92mm CPU CoolerInternet Surfing 30C - 960 - 1100 RPMGaming L4D2 37C - 1200񳅨 RPMAMD Phenom(tm) II X3 740 3.00 GHz (X4 three.25 GHz) None None

Comment:
does specifically what it really should. sleeved wiring is a good touch. it is a bit long but not a large deal. a bit pricey. at ū it may possibly be worth hunting in to finding a single of the arctic pwm fans that come with one particular of these built in

Comment:
Worked perfectly on my Hyper 212+ to setup Push/Pull cable is a bit long but it truly made my cable management even simpler no complains right here! none Excellent!

Comment:
Functions excellent for my CM Hyper 212 plus. If you want your push/pull set up controlled by the one CPU fan connector on yur motherboard search NO further. This it. Couldn't be happier. ^_^ Seeing ppl rate this solution low mainly because THEY didn't realize how this thing functions...*sigh* I'm buying one more for my CM TX3 cooler for my other rig also. Listen to the review by geniusTFLord. Quite considerably sums it up well. Don't hesitate.

Comment:
Functions fantastic! makes each fans sync and run at same speeds and relates to cpu temp. When it gets hot the fans spin more rapidly then cools down and fans go back to idle speeds. None

Comment:
Excellent cable to get two PWM fans to run off of a single PWM slot on the motherboard. None!

Comment:
Braided cover more than the cable, good develop on the connections (tough), A "True PWM Cable" in contrast to a past overview I read, Utilized with the ideal fans and your Computer will run quiet and cool like mine does now. none

Comment:
Performs like a charm. No cable wrapping from the factory I use this to power the two fans on my CPU radiator off the mobo PWM output.

Comment:
this item is utilised to operate 2 fans as if it had been a single fan.you can use 2 or 3 linked y conectors and all fans will have there speed ajusted by the mother board at the similar time.im using two linked appropriate now with three fans all have identical speed given by mother board. mother board can only read one rpm per header thats why there's only one that has 4 pins although the other has three none you guys ought to realy do beter reserch befor complaining about weather or not it requires the fourth pin on the second conector.you need to understand somones ingenierd this for a purpose,not to mention you cant find 1 with all three conectors getting four pins that must be a hint

Comment:
Works effectively, I have my case supply fan and CPU fans tied with each other off the CPU plug, adore how they get quiet when idle and crank up below load working with bios handle, utilizing 4 wire PWM fans none wonder how quite a few fans you can SAFELY string off one connection, diverse fans have various minimum RPMs so the fan on the feedback can transform the min on the other,

Comment:
Works perfectly as described. Wired correctly for PWM. none No cost shipping would have been nice newegg..

Comment:
This nicely sleeved cable is for 4 wire PWM fans and performs specifically as advertised, the tach wire only goes to one particular fan which is how it really should be so the motherboard isn't trying to read the speeds of two fans.The wire that controls fan speed is intact, goes to each fans and controls each fans.Ahead of you guys post poor reviews you need to read the manufactures web page and learn how factors operate... sheesh. None

Comment:
Its a great cable its NOT AS ADVERTISED. As the other reviewer has stated, it doesn't just split the PWM connection into two 4 pin connectors, it splits it into A single four pin connecter even though the other is only 3 pins!Extremely annoying as this makes the cable somewhat....useless simply because you need four pins to truly control the speed of other fans. Returning as of now

Comment:
Great good quality, strong None I know of Don't know how it operates in a setup it is meant for, but I purchased it to replace a 4 wireǚpin CPU fan cable from a CPU fan I had broken a wire from its metal connecter inside the principal plastic connecter. It was the fastest/easiest/best resolution for me ;)

Comment:
excellent product none forgot to mention in my prior review im making use of 3 pin fans on the conector with three pins so you only require one pwm fan and rest can be normal three pins and speeds will ajust by mother board shure wish there was a way to edit my evaluations

Comment:
Fantastic good quality, low value. Description claims this Y-cable has one particular four-pin female connector, and two four-pin male connectors. What I received is a Y-Cable with one particular four-pin female connector (for the CPU connector on the MOBO); one particular four-pin male connector on one particular end of the Y, but a 3-pin male connector on the other finish of the Y. You could use this Y-Cable to hookup two PWM fans, but only a single of the MOBO's PWM control, the other fan would present the fan's current speed, but would not be controlled by PWM. If you look at the enlarged photo of this Cable, you will see what I mean...--- This is the second mislabeled PWM splitter cable that I have received from Newegg (two unique brands). If you are significant about making all of your fans PWM controlled, the simplest solution is to use AC for all of your situation fans...

Comment:
This item functions specifically as advertised. You only will need 1 RPM signal from one particular of the fans to communicate with the motherboard. The speed is controlled by the 4th pin. If the fans are identical, the RPM's will be identical and change with each other. You can make your personal by splicing the black, red, and blue wires (pins 1, 2, and 4) with each other and One yellow wire (pin 3). I wish individuals who claim to have a high tech level would try out a item initially before rating it. It works and it's low-cost. Yes, you can make your personal, but at ū it's a excellent deal.

Comment:
A lot of length, look good, well produced. Completely pleased about this item. Nada I searched on Newegg for a PWM Y-splitter and these did not come up. A much less attractive, more high-priced one did. This one particular did show up when I searched on "Gelid" (I knew that Gelid produced these.

Comment:
A couple of reviewers mentioned that this is not a true pwm splitter because one particular of the connectors is missing one of the pins. It is missing the 3rd pin. The initial 2 pins are for power and ground. The third pin is for rpm readings. The 4th pin (present in each leads) is utilised for PWM (speed control). That is why you can have prm readings from a 3 pin fan. Hope this clears up any confusion.I am assuming that they didnt include things like the 3rd pin due to the fact it would read both fans rpms on the 1 fan header and add them together therefore top to a false reading. persons who give a fantastic product 1 egg when thay are misunderstanding how an item operates. If you will need a pwm splitter, this looks like it will do the job nicely.

Comment:
Works as advertised. Nice excellent cable for the cash. None