Location: Home > Computers > Components > Controllers > Sabrent IDE Ultra 100-133 to Serial ATA to Mini Converter

Sabrent IDE Ultra 100-133 to Serial ATA to Mini Converter

Sabrent IDE Ultra 100-133 to Serial ATA to Mini Converter (Sabrent: SBT-SCIDE)
VPN: SBT-SCIDE
Vendor: Sabrent
Price: $0.00 - $0.00 CAD from 0 stores
» Email this product to a friend   » Write a review
» Discuss on forum   » Post your deal
  Store Product Price  

Product Reviews

Sabrent IDE Ultra 100-133 to Serial ATA to Mini Converter
26%
Excellent
20%
Very Good
13%
Average
11%
Below Average
16%
Poor
Rating: 6.79/10
Galen
Rating:

Review Date: 09/04/13
Comment:
YOU ARE NOT SUPPOSE TO USE JUMPERS WITH THIS Product!! This conversion eliminates the use for jumpers, so if you attempt to use a jumper it won't boot. I've borrowed my buddy's for a tiny while, worked great for me. directions could not aid stupid men and women. I'll will be ordering 1 of these myself not a terrible cost, I've seen some for $xx.
Vicky
Rating:

Review Date: 08/29/13
Comment:
it fit perfectly into my IDE difficult drive. and worked instantaneously. i did nevertheless have to download new SATA drivers for my motherboard ahead of it would quit showing it as a usb drive.
Quade
Rating:

Review Date: 08/12/13
Comment:
Functions! Don't even notice that I'm not doing actual sata. I would undoubtedly reccomend this drive, at least for difficult drives. It took a tiny fiddling with jumpers to get it to perform. I needed the drive set to master and the device jumper left where it was for it to function. At times when I move sata ports on the mobo it'll stop recognizing, but a handful of reboots and a lot more fiddling and it functions again.
Rollin
Rating:

Review Date: 08/11/13
Comment:
It does precisely what it supposed to do; I can plug my old IDE difficult drives into SATA connectors on the motherboard. The boards look flimsy but after it's installed, you won't be handling it any longer. (I didn't attempt ((or need)) it for any optical drives so I can't comment about that.) I'm not trying to sound harsh; however, I actually don't fully grasp peoples' confusion with this item. 1) It’s a SATA connector, there is no Master/Slave to believe about, of course you'd set the jumpers to "cable select". two) Why would you expect a SATA power connector? The drive you're plugging it into is nonetheless an IDE drive; it's just emulating a SATA drive.
Alijah
Rating:

Review Date: 08/09/13
Comment:
None Ordered two units. The 1st worked for about 2 days then died. Went to use the other one particular and the only factor in the box was the splitter cable. Not expense efficient to rma the units.
Rowa
Rating:

Review Date: 07/29/13
Comment:
Decent design, simplistic, and you can't seriously screw it up. Study the box label. Why would they contact it a "SATA-to-IDE" when they convert IDE drives to SATA format?? It Really should be referred to as an "IDE-to-SATA converter"! Not a lot else, people just want to believe prior to they name/market/sell a product. Note: NewEgg has nothing at all to do with this challenge, they are generally incredible.
Clementine
Rating:

Review Date: 07/17/13
Comment:
it works but not for all burners in spite bios see and recognize both benq and hp drives windows xp boots only with HP
Jania
Rating:

Review Date: 07/12/13
Comment:
Does convert the interface. I place numerous of these into a server exactly where we had a motherboard die and the new board was SATA and all the devices have been PATA. The challenge is that the SATA CONNECTOR IS NOT A LOCKING CONNECTOR. So if you move something inside the server it is extremely straightforward to have 1 of these cables pull off. This adapter needs to be redesigned with a locking connector.
Rafer
Rating:

Review Date: 07/08/13
Comment:
Board does what it was made to do. Sped up transfers by about 10 MB/sec. IDE would max out at about 40 MB/sec (when lucky) this simply pushes it to 55 MB/sec. Particularly IDE drives with a massive cache size Ƙ MB). Appreciate the solution None so far. I have mine in a case which is really tigh, so the sata connectors are pushing against the outside door, causing the connectors to remain in. Otherwise they tend to "fall", in that they are sort of angled with the weight of an SATA cable. Nothing at all genuinely, NewEgg shipping was rapidly and trustworthy as usually.
Huyen
Rating:

Review Date: 06/29/13
Comment:
Keeps legacy drives alive Undocumented. Like all back-of-drive printed circuit adaptors, it could short. SATA connector does not lock. May well want a jumper block if you have to adhere to the identical guidelines I did. I would not have gotten this beastie functioning devoid of the aid of other reviewers here. Thank you all!Standard guidelinesɅ - Set the drive to Cable Choose. two - Discover the jumper pair labelled 'J2'. The labels are In between the jumper header and the adjacent SATA connector, and I had to trim away some stray plastic on the jumper header to see them. Spot a jumper block on J2.3 - Connect to drive, connect cables, run.I have not however been in a position to test for performance.
Sunny
Rating:

Review Date: 06/03/13
Comment:
Great concept if it was trusted. I did handle to get this item to work, but I discover it very 'hit or miss'. All was fine, till I rebooted my Pc, now I can't see the HD in Vista. Shows up in BIOS. This is without having changing anything in the setup. Lastly took it out of my system and hooked up my DVD burner and ATA HD in a master/slave config. on the single IDE channel. Not the ideal but at least it operates.You take your chances with this item, various men and women appear to be happy with it. I want I was as well.
Jaguar
Rating:

Review Date: 06/01/13
Comment:
none this was a waist of money, 1st issue that occurred when i turned my computer system on was a spark followed by smoke. it died immediately. do not get this item, it sucks get a different far better a single
Colton
Rating:

Review Date: 05/07/13
Comment:
this issue fit completely on my two dvd -burners and it easily converted the IDE to SATA and a extremely easy setup had some issues at very first with the Pri and Master but you just need to have to alter your ide pins to Cable Pick i would deferentially advise somebody to purchase this if they don't wanna waste a completely fantastic ide drive as an alternative of obtaining a complete new sata drive
Rosamund
Rating:

Review Date: 05/06/13
Comment:
It recognizes my old Sony CD-RW drvie (Model CRS140E) as a CD-ROM. When it is working, I have no troubles reading the CD from the drive. It will not detect the Sony CD-RW drive for the duration of warm reboot. Every single time when I want to use this drive (on ECS P965T-A motherboard with JMicron Controller), I want to cold boot my Computer (Win XP Pro). Since it only register the CD-RW drive as a CD-ROM, for that reason I can not burn any CD with it unless I connect it to the JMicron IDE controller. I had a tough time attempting to load Ubuntu on a new develop with Intel Core 2 Duo E6400 CPU and Seagate 300MB Sata drive. Hoping that I will be capable to convert the Sony CD-RW IDE drive to Sata that will permit me to load Ubuntu. However, that has other problems with Ubuntu (Both 6.06 and 6.10) versions.
Shandi
Rating:

Review Date: 05/04/13
Comment:
it functions as a storage drive/backup. I purchased an SSD for my older Dell desktop computer in hopes I would be capable to speed up the machine (the motherboard was a IDE interface but the SSD was SATA). When I attempted to use it to boot the laptop off of the drive - it wouldn't perform... I did the same factor for a newer SATA toshiba difficult drive and it was even slower than the significantly less then great 5 year old internal WD HDD. It performs if you want to store files but didn't look to perform nicely as a boot drive (for SSD or HDD).
Seamus
Rating:

Review Date: 05/02/13
Comment:
Non They didn't operate for me. I purchased two of them to salvage a DVD drive and a hard drive neither is recognized by the new mother board. Save your cash don't buy these.
Estrella
Rating:

Review Date: 04/03/13
Comment:
Conceivably can be a fantastic enable in the right applications after you get it functioning. It is uncomplicated, inexpensive and tries to fill a genuine need to have as the globe converts to SATA Even though physical installation is simple, the lack of documentation and support presents a true challenge to overcome unexpected design and style flaws. The suggestions in these newegg evaluations had been most helpful in receiving the board going. Heed the suggestion of other reviewers here to put tape on the underside of the board, so that the exposed solder joints do not short out against the really hard drive case. Also, if you locate that your personal computer begins to freeze randomly and unexpectedly and you have attached the board to your boot drive, I recommend removing the board or attempting it on a non-boot drive to see if that clears the dilemma.
Berenice
Rating:

Review Date: 03/28/13
Comment:
Uncomplicated to install. After about an hour this device caused my tough drive to overheat. I unhooked it, and attempted one more drive in another pc and it did the similar point. Now both drives aren't even detectable by their manufacturer's diagnostic software program.Fantastic idea for a product - but don't threat it. Who of you are prepared to danger your information?
Sierra
Rating:

Review Date: 03/17/13
Comment:
efficiency, installation, cost, low profile none presently employing two of them in a Raid 1 config, rapid and easy to use
Rafal
Rating:

Review Date: 03/16/13
Comment:
It eventually worked and then worked fine. Took a tiny finagling to make it function alright. Once it got going, it was alright.
Socorro
Rating:

Review Date: 02/20/13
Comment:
small, fits in slots Installed it, tried to boot up computer system, took 15 MINUTES! This converter sucks. Tends to make tough drive really slow. Invest some money and get 1 that performs Acquire a better 1.
Edith
Rating:

Review Date: 01/18/13
Comment:
This thing has saved my rear several occasions. Like how dell doesn't consist of PATA on it's newer systems. I haven't had a problem with it however. Pair this with Acronis, a three.5-2.five notebook adapter and your set. I had one created by Silicone Image in the previous. That one had a clear plastic chassis on it. I can't discover them any far more. This is that one particular, no case. That is the only purpose for 4Ǜ. Don't be violent with it. They can snap.
Arnon
Rating:

Review Date: 01/16/13
Comment:
Low cost, apparently great compatibility, simple to set up. I hooked it up to a 300GB Maxtor DM10 in the 2nd SATA bay. It is the boot drive now, there have been zero issues. None so far. For installation in a G5, you require either a power line splitter, or an adapter from SATA power connector to regular 4-pin. This board's integrated wire harness requires a typical four-pin power cable, and splits it to power the board and the attached drive. It does not accept a SATA power connector.
Keelin
Rating:

Review Date: 01/10/13
Comment:
None Does not operate. Waste of my cash.
Anthony
Rating:

Review Date: 12/28/12
Comment:
Extremely smaller size, uncomplicated install. Fits completely in the MAC G5 Tower. Personal computer instantaneously reconized the drive and mounted no dilemma. (Drive was prevoiusly in my G4) Energy plug is different, (MAC only) I utilised this item to set up a ATA drive in my Mac G5 that only makes use of SATA drives. Only issue was the Mac Power connector is different than the plug on this adaptor. Ended up employing a Y spliter on the energy cable to the Optical drive to power this unit. Performs properly. Highly recomend for G5 owners with old ATA drives.
Click Here Show More Product Reviews

Product Features

IDE Ultra ATA-100/133 to SATA Mini Converter
This Ultra ATA-133-to SATA mini converter features a standard 40 pin ATA port and can interface to a parallel Ultra ATA (IDE) devices (hard disk, CDROM, etc). It accepts SATA commands through the Serial ATA interface from the host, decodes the commands and converts them to parallel ATA commands to the device. Response from the device through the parallel ATA bus are deciphered, processed and converted to SATA protocol and sent to the host.

This Ultra ATA-133-to-SATA Converter Board supports the Serial ATA Generation 1 transfer rate of 1.5 Gb/s (150 MB/s) on the serial side and is compatible with Ultra ATA-133 on the parallel ATA side.

All EIDE type DVD / DVD-RAM / CD-ROM / CD-RW / HDD become new serial ATA devices!

Attache this Mini Converter board to the back of all types of ATAPI, ATA/133, ATA/100, ATA/66, ATA/33, EIDE and IDE storage devices (such as Hard Disk, DVD, DVD-RAM, CD-ROM, CD-RW, MO, etc.) and make them become new Serial ATA Devices and meet new Serial ATA standard.

This dangle board can support HDD larger than 137GB. The standard 40-pin ATA port can interface to a parallel Ultra ATA device. It accepts SATA commands through the Serial ATA interface from the host, decodes the commands and converts them to parallel ATA commands to the device. Response from the device through the parallel ATA bus is deciphered, processed and converted to SATA protocol and sent to the host.

All your old DVD / DVD-RAM / CD-ROM / CD-RW / HDDs become new serial ATA devices and meet new serial ATA standard !!


Specifications

  • Supports all types of devices:
    - ATAPI
    - ATA/133
    - ATA/100
    - ATA/66
    - ATA/33
    - EIDE
    - IDE
  • Capacity: Support HDD larger than 137GB
  • Transfer rate: 1.5 Gb
  • Compliance: Serial ATA 1.0 Specifications

Features

  • Support Spread Spectrum in receiver
  • Converts parallel ATA hard drive to Serial ATA
  • Supports ATA/100 or ATA/133 IDE hard drive
  • Includes Y Power Cable

Product Specifications

Model
BrandSABRENT
ModelSBT-SCIDE
Spec
TypeIDE to SATA
SpecificationsSupports all types of ATAPI, ATA/133, ATA/100, ATA/66, ATA/33, EIDE and IDE storage devices (such as DVD, DVD-RAM, MO, CD-ROM, CD-RW, Hard Disk) Can Attaches to all types of ATAPI, ATA/133, ATA/100, ATA/66, ATA/33, EIDE and IDE storage devices (DVD, DVD-RAM, MO, CD-ROM, CD-RW, Hard Disk) 48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB Mini Board size, No space wasted Breaks Capacity-Limit to support HDD larger than 137GB Mini board size, no space wasted High transfer rate of 1.5 Gb/s Compliant with Serial ATA 1.0 Specifications Support Spread Spectrum in receiver Converts parallel ATA hard drive to Serial ATA Supports ATA/100 or ATA/133 IDE hard drive Compliant with Serial ATA 1.0 specification Compliant with ATA specifications Compatible with Ultra ATA 133
Features
FeaturesThis SATA-to-Ultra ATA-133 Converter Board is a converter solution for the Parallel Ultra ATA Device. It has a standard 40 pin ATA port can interface to a parallel Ultra ATA (IDE) devices (hard disk, CDROM, etc). It accepts SATA commands through the Serial ATA interface from the host, decodes the commands and converts them to parallel ATA commands to the device. Response from the device through the parallel ATA bus are deciphered, processed and converted to SATA protocol and sent to the host.This SATA-to-Ultra ATA-133 Converter Board supports the Serial ATA Generation 1 transfer rate of 1.5 Gb/s (150 MB/s) on the serial side and is compatible with Ultra ATA-133 on the parallel ATA side.ALL EIDE Type DVD / DVD-RAM / CD-ROM / CD-RW / HDD Become New Serial ATA Devices! Attaches this Mini Converter board to back of all types of ATAPI, ATA/133, ATA/100, ATA/66, ATA/33, EIDE and IDE storage devices (such as Hard Disk, DVD, DVD-RAM, CD-ROM, CD-RW, MO) and make them become new Serial ATA Devices and meet new Serial ATA standard.This dangle board can support HDD larger than 137GB. The standard 40 pin ATA port can interface to a parallel Ultra ATA devices. It accepts SATA commands through the Serial ATA interface from the host, decodes the commands and converts them to parallel ATA commands to the device. Response from the device through the parallel ATA bus are deciphered, processed and converted to SATA protocol and sent to the host.All Your Old DVD / DVD-RAM / CD-ROM / CD-RW / HDDs Become New Serial ATA Devices and Meet New Serial ATA Standard !!
Manufacturer Warranty
Parts1 year
Labor1 year

Similar Products

PriceBat.ca is 100% Canadian Own premier price comparison shopping site. Easy to search & compare prices of computer products, electronics and games at Canada online stores.