COOLER MASTER Hyper 212 Plus RR-B10-212P-G1 120mm sleeve CPU Cooler

Comment:
Good cheap and easy way to add extra cooling. Have it running on two i7 systems. Works great.

Comment:
Was fairly complicated to install on the motherboard but haven't had any issues afterwards. Glad it fit in my case as it's very tall with the 120 mm fan. I do like how it has the option to install a 2nd on the other side.

Comment:
Great product, good bang for your buck as you could say

Comment:
J'ai acheter ce cpu cooler pour aller avec un 2500K OC a 4Ghz sans probleme. Temperature en full load en bas de 75 degrÉ, tres satisfait

Comment:
Easily one of the best "bang for buck" coolers.Easy to put on, cools awesome. A no brainer for anyone not willing to spend $60+

Comment:
great none

Comment:
Considering how cheap self contained watercooling setups are getting this might not be as great of a purchase, but this does the job for cheap.

Comment:
Great cooler, despite its low cost. My Phenom II X3 740 Unlocked to 4 cores hovers around 30C on stock voltage. It's never hot to the touch. Direct contact pipes makes it a very efficient cooler.

Comment:
Great cooling! In no way gone past 30c Check your case cpu coolerheight limit, seriously huge cooler.

Comment:
I've used dozens of these in builds, and used one on my own system for a bit. Performs nearly as well as some of the more expensive CPU coolers that I've tried (CNPS10x Extreme, Scythe Mugen II, etc.) If you have an unlocked processor, don't hesitate to slap one of these in there and have some fun.

Comment:
Installed this on a micro-atx, 775 motherboard. I took a gamble buying it, since you can't return them for exchange. Installation took approx 40 minutes. The included adaptor is brilliant, the swiss army knife of adaptors. The included kit was a very nice touch, especially the thermal paste & thumb screw.Once installed this beast towers over the motherboard like a watch tower. Although it's about 3mm away from my ram sinks, clearance was alright. Cranked an intel e5200 from 2.5ghz to 3.45ghz & ran prime95 all night. With ambient temperatures 20c, under load max = 45c. So thats just where it needs to be. I would recommend screwing in a cross pattern & make sure everything is nice & tight because if even 1 screw is loose your in trouble.With the option to put another 120mm fan, should the need justify it & its compatability with various sockets this heatsink is a winner. Purchased additional unit for a friend.

Comment:
Wonderful cooler for my i7 870 O/C'ed to 3.6. with stock cooler and fan at 100%, idled at 52 deg. Run prime for much more than ten seconds and it was in the 100's. With this cooler, idles at 33ኂ and prime doesn't take it past 70 degrees. At 50% fan speed! For whatever reason, Cores 1 and three are consistently 6 degrees hotter at idle than 2 and 4. Applied arctic silver 5 paste in a vertical line as shown on internet site. The only explanation is the heatpipes aren't completely flat on the surface that contacts the processor. Not enough to knock an egg even though, still very affordable temperatures. Got it for 28 bux from a various retailer. Can't beat it! Sorry, NewEgg.

Comment:
I bought this cooler as a replacement for my aging and dying Zalman cooler. It was super cheap ($23 pm'd), which was the primary reason I went for it. It was originally on my E8500 (3.8) keeping temps below 60deg, even after folding for long periods of time. Since then, I have put a QX9650 in my system (overclocked to 3.81) and it does a great job keeps temps at 60deg or below ALL the time (again, even after folding for long periods of time!).A second fan can easily be added for push pull, making it an even more effective cooler.One downside (if you can call it that) is that it is big (the ends of the heatpipes nearly touch the side panel of my P182!) Installing the heatsink also required my to dissemble my system to put the backplate on (slightly annoying, but this isn't really an issue with the cooler, more with the case), so it did take me a while to install.Overall, very satisfied!

Comment:
Low-cost. Tension tested my i7 950 system (just five runs) with Linpack and the core temps (all 8 threads) by no means went past 61C. With just a single fan. Ha! Plain seeking but unassuming. My CM 430 case and the affordable EVGA cool board maybe helping it. Plus no OC coz no require with the effective CPU.Idle temps are 32 - 37 as I type. Then once more, it only cools a CPU that gets three% load tops when surfing.

Comment:
Great air cooling solution, would buy in the future.

Comment:
Its massive Its enormous

Comment:
Very good cooling, for the price. I installed it for my LGA1155 motherboard. Very nice. I recommended it for mid range computer who want to spend not too much for a nice value gaming computer!

Comment:
This cooler works amazingly, I added another fan for push / pull setup and cant complain. Great improvement from the stock cooler and a must have when overclocking. Great for the Price! Pretty big so make sure you have the room in your case.

Comment:
using on AMD Athlon X2 6400+vs 4600+ stock cooler, dropped idle temp by almost 10 degrees!vs 4600+ stock cooler, does not see over 52 degrees anymore!read the reviews, best bang for buck cooler!

Comment:
Keeps my temperatures very low all the time. Price for performance is incredible. If I were to recommend this to someone for their gaming system, I would definitely recommend this heat sink to them!

Comment:
I picked up one of these to put on an i5 2500k on a ASRock Z68 EXTREME3 GEN3. The heat sink is big, but it does also support two 120mm fans. it also includes all the hardware to do so!My main issue with the heatsink is that it's a pain to get sitting straight. The bracket is separate from the heatsink base so that you can turn it around for a different application, but it's finicky. There's a little nub that you are supposed to be able to click the bracket into but it still has some play.I had to mount it a couple times before getting it right.As for performance, the i5 is running at 4.6GHz and stays around 52-55C! No issues at all!

Comment:
Using with an E8400 for a year now. OC'ing to 4Ghz and doesn't break 55c in game. I'll be using this on my i5 once it arrives.

Comment:
Best cooler, for first time computer builder easy instillation. And the temperature with Prime 95 with over 1hour of duration the temps. averaged 60C.

Comment:
Very easy to install. Keeps my i5 2500k idling at 34 degrees and rarely hits 50 when operating. You really can't beat this heatsink for the price. I would buy again and again.

Comment:
Simple install. Not as large as some other coolers (it's nevertheless Big). Keeps temperatures low at high loads. none I put this on an asus p8p67pro board, with ripjaws memory and had a lot of room. I have an i5-2500k overclocked to 4.3 and it runs at about 59C below load. I'm confident I can go quicker with this.